2168 - Equipment no longer required due to the Retirement of the Directors of Robinson Engineering & Others – Items removed for convenience of loading – Phase 2
Engineering
L'enchère s'est terminée le
Temps restant
'Description de l''enchère'
Please Note: These Items are located in Cheshire & Nelson
Please Note: The Lots which are located in Cheshire will be loaded free of charge to a suitable vehicle. Blocking and Securing however will be at the cost of the purchaser
Prime d'acheteur
'La prime d''acheteur sera fixée à 15.00%.'
TVA
'La taxe sur la valeur ajoutée s''élèvera à 20.00%.'
Temps de consultation
Viewing by Appointment with the Auctioneer Only, Please contact our office on: + 44 (0) 121 328 2424
* Remarque : Toute traduction effectuée à l'aide de Google Traduction n'est pas garantie en tant que traduction exacte et n'est fournie qu'à titre indicatif. La description du lot en anglais est la description prédominante et bénéficie de la meilleure connaissance du commissaire-priseur. Cependant, l'exactitude n'est pas garantie et doit être vérifiée par l'acheteur avant d'enchérir.
Avis aux acheteurs
Date limite de paiement
'Date limite d''apurement'
'Agents d''expédition'
Sous-traitants pour le stockage
Exporter/Importer des détails du Royaume-Uni
Lots 21-30 de 75
Lot 19: Kingsland 60XA Hydraulic Ironworker
Kingsland 60XA Hydraulic Ironworker Capacity 60 Ton, Punching 28 x 15 mm, Shearing 300 x 15 mm, Angle 120 x 12 mm, Section 40 mm Round, Notching 42 x 100 x 10 mm
Please Note: - This Item is located in Cheshire and will be loaded free of charge to a suitable vehicle. Blocking and Securing however will be at the cost of the purchaser.
Lot 20: Edwards " Jaws V" Hydraulic Iron Worker
Edwards " Jaws V" Hydraulic Iron Worker, 65 Ton Cap. Flats 24" x 3/8". Angles 5" x 5" x 1/4". Punches 1 1/16 dia hole in 3/4" Plate. Notching 2 1/2" x 6" x 3/8"
Please Note: - This Item is located in Cheshire and will be loaded free of charge to a suitable vehicle. Blocking and Securing however will be at the cost of the purchaser.
Lot 21: Colchester Mascot 1600: Gap Bed Centre Lathe
Colchester Mascot 1600: Gap Bed Centre Lathe, 17" Swing over bed, 28" Swing in gap, 100" Between Centres with 3" Spindle bore, Speeds 20 - 1600 rpm.
Please Note: - This Item is located in Cheshire and will be loaded free of charge to a suitable vehicle. Blocking and Securing however will be at the cost of the purchaser.
Lot 22: Colchester Mascot 1600 Gap Bed Centre Lathe
Colchester Mascot 1600 Gap Bed Centre Lathe, 17in Swing over bed, 28in Swing in gap, 60in Between Centres, 3in Spindle Bore. Speeds 20 - 1600rpm with Quick Change Tool Post, Newall DRO
Please Note: - This Item is located in Cheshire and will be loaded free of charge to a suitable vehicle. Blocking and Securing however will be at the cost of the purchaser.
Lot 23: Colchester Mascot 1600 Gap Bed Centre Lathe
Colchester Mascot 1600 Gap Bed Centre Lathe, 17'' Swing over bed, 28'' Swing in gap, 60'' Between Centres, 3'' Spindle Bore, Speeds 20 - 1600rpm, Three Jaw Chuck, Dual Dials, Four Way Tool Post. Newall DRO
Please Note: - This Item is located in Cheshire and will be loaded free of charge to a suitable vehicle. Blocking and Securing however will be at the cost of the purchaser.
Lot 24: Dean Smith Grace Type 1709 x 60 Gap Bed Centre Lathe
Dean Smith Grace Type 1709 x 60 Gap Bed Centre Lathe, 17'' Swing over bed, 24'' Swing in gap, 60'' Between Centres, 3'' Spindle Bore, Speeds 8 - 900rpm, Dual Dials, Power Drilling Attachment.
Please Note: - This Item is located in Cheshire and will be loaded free of charge to a suitable vehicle. Blocking and Securing however will be at the cost of the purchaser.
Lot 25: Mitchell Gap Bed Centre Lathe
Mitchell Gap Bed Centre Lathe, 16'' Swing over bed, 32'' Swing in gap, 48'' Between Centres, 3'' Spindle Bore, Speeds 22.5 - 750rpm. 4-Jaw Chuck, Three Point Steady.
Please Note: - This Item is located in Cheshire and will be loaded free of charge to a suitable vehicle. Blocking and Securing however will be at the cost of the purchaser.
Lot 26: Modig Type RBM 28 B Radial Arm Drill
Modig Type RBM 28 B 30in Radial Arm Drill, 3 Morse Taper Spindle, Speeds 100 - 1280rpm, Swivel Table Size 450 x 450mm, Power Feed.
Please Note: - This Item is located in Cheshire and will be loaded free of charge to a suitable vehicle. Blocking and Securing however will be at the cost of the purchaser.
Lot 26a: XYZ CNC 400 Bed Type Milling Machine
XYZ CNC 400 Bed Type Milling Machine, Table Size 51in x 12i with Fanuc OM Control
Please Note: - This Item is located in Cheshire and will be loaded free of charge to a suitable vehicle. Blocking and Securing however will be at the cost of the purchaser.
Lot 27: Bridgeport Series 1 Turret Mill
Bridgeport Series 1 Turret Mill, 2 HP Vari-Speed Head, Table size 42in x 9in, R8 Taper with Power Feed Table Long & Cross. Heidenhain DRO to X Axis (1980)
Please Note: - This Item is located in Cheshire and will be loaded free of charge to a suitable vehicle. Blocking and Securing however will be at the cost of the purchaser.