2137 - Equipment no longer required due to the Retirement of the Directors at Sapphire Engineering & Fabrication and Others - items removed for the convenience of loading
Engineering
L'enchère s'est terminée le
Temps restant
'Description de l''enchère'
Location: These Items are located in Cheshire and will be loaded free of charge to a suitable vehicle. Blocking and Securing will be at the cost of the purchaser
Prime d'acheteur
'La prime d''acheteur sera fixée à 15.00%.'
TVA
'La taxe sur la valeur ajoutée s''élèvera à 20.00%.'
Temps de consultation
Viewing by Appointment only with the Auctioneer, please contact our Office on: + 44 (0) 121 328 2424
* Remarque : Toute traduction effectuée à l'aide de Google Traduction n'est pas garantie en tant que traduction exacte et n'est fournie qu'à titre indicatif. La description du lot en anglais est la description prédominante et bénéficie de la meilleure connaissance du commissaire-priseur. Cependant, l'exactitude n'est pas garantie et doit être vérifiée par l'acheteur avant d'enchérir.
Avis aux acheteurs
Date limite de paiement
'Date limite d''apurement'
'Agents d''expédition'
Sous-traitants pour le stockage
Exporter/Importer des détails du Royaume-Uni
Lots 1-10 de 69
Lot 1: Union Bft 80/2 Horizontal Boring Facing & Milling Machine
Union Bft 80/2 Horizontal Boring Facing & Milling Machine, 80mm Spindle Dia. 500mm Facing Head. 1125mm x 1000mm Table Size
Please Note : This Item is located in Cheshire and will be loaded free of charge to a suitable vehicle. Blocking & securing however will be at the cost of the purchaser
Lot 2: Herbert Type 28A Vertical Milling Machine
Herbert Type 28A Vertical Milling Machine. 28" x 85" Table, 62" Long Travel, 28 1/2" Cross Traverse. 30 1/2 " Max Spindle Nose to Table, Throat 26 3/4", Spindle Nose Dia. 5 1/16". Spindle Taper 50 ISO. 960 rpm 16 x Spindle Speeds 12 - 360 rpm, 1430 rpm 16 x Spindle Speeds 18 - 540 rpm.
Please Note : This Item is located in Cheshire and will be loaded free of charge to a suitable vehicle. Blocking & securing however will be at the cost of the purchaser
Lot 3: DS&G Type 21 x 96 Gap Bed Centre Lathe
DS&G Type 21 x 96 Gap Bed Centre Lathe. 22" Swing over bed, 35" Swing in gap. 96" Between Centres and 3 1/2" Spindle Bore. S/No. 35571-1-65
Please Note : This Item is located in Cheshire and will be loaded free of charge to a suitable vehicle. Blocking & securing however will be at the cost of the purchaser
Lot 4: Mostano Type 1M63HT3 Gap Bed Centre Lathe
Mostano Type 1M63HT3. Gap Bed Centre Lathe. 27" Swing over bed, 36" Swing in gap, 10ft between centres, 4 1/4" Spindle Bore, 15" 4 Jaw Chuck, 3 Point steady (1996)
Please Note : This Item is located in Cheshire and will be loaded free of charge to a suitable vehicle. Blocking & securing however will be at the cost of the purchaser
Lot 5: Fielding & Platt Ltd Hydraulic Horizontal Press
Fielding & Platt Ltd Hydraulic Horizontal Press, Capacity 100 Ton, Ram Size 10" Dia. Platen size 48" x 46"
Please Note : This Item is located in Cheshire and will be loaded free of charge to a suitable vehicle. Blocking & securing however will be at the cost of the purchaser
Lot 6: Haco 3 Roll Double Pinch Bending Rolls Type 3HBR176A
Haco Type 3HBR176A 3 Roll Double Pinch Bending Rolls, 1750mm Length of Roll, 6mm Bending Cap. 150mm Dia of Rolls. Hardened Rolls 50-55 HRC. Hydraulic Conical Bending, Hydraulic Drop End, Hydraulic Side Positioning Readouts, Hydraulic Overload Protection System with Wire Safety System. (2007)
Please Note : This Item is located in Cheshire and will be loaded free of charge to a suitable vehicle. Blocking & securing however will be at the cost of the purchaser
Lot 7: Kingsland Type SST 3006 Hydraulic Power Guillotine
Kingsland Type SST 3006 Hydraulic Power Guillotine. Capacity 3000mm x 6mm with Power Back Gauge.
Please Note : This Item is located in Cheshire and will be loaded free of charge to a suitable vehicle. Blocking & securing however will be at the cost of the purchaser
Lot 8: Edwards " Jaws V" Hydraulic Iron Worker
Edwards " Jaws V" Hydraulic Iron Worker, 65 Ton Cap, Flats 24" x 3/8" or 14" x 1/2". Angles 5" x 5" x 1/4" or 4" x 4" x 3/8" Punches 1 1/16 dia hole in 3/4" Plate. Notching 2 1/2" x 6" x 3/8".
Please Note : This Item is located in Cheshire and will be loaded free of charge to a suitable vehicle. Blocking & securing however will be at the cost of the purchaser
Lot 9: Edwards 35 Ton Mechanical Iron Worker
Edwards 35 Ton Mechanical Iron Worker, Cap Angle & Tee 3" x 1/4", Cropping Round 1 3/16", Square 1", Punching 7/8" Dia x 3/8" or 11/16" dia x 7/16". Notching 5/16" Thickness with Motor 2 HP.
Please Note : This Item is located in Cheshire and will be loaded free of charge to a suitable vehicle. Blocking & securing however will be at the cost of the purchaser
Lot 10: Barnes Pyramid Bending Rolls
Barnes Pyramid Bending Rolls. Capacity 48" x 1/8". Size of Rolls 48" x 5" Top & 4" Bottom.
Please Note : This Item is located in Cheshire and will be loaded free of charge to a suitable vehicle. Blocking & securing however will be at the cost of the purchaser